Akai tv manual lct42z6tm. Akai LCD TV 42 inch Television Repair LCT42Z6TM 2019-01-26

Akai tv manual lct42z6tm Rating: 5,6/10 1861 reviews

AKAI LCT42Z6TM Service Manual download, schematics, eeprom, repair info for electronics experts

akai tv manual lct42z6tm

Any question, please contact me. The 35V volt 100uf capacitors were replaced with 50v capacitors. Replace the board, we tested by putting the board back. Remove the two screws to remove the power jack from the back. Lift the back up from the left to the right. I have not replaced any on the power supply board. Another note, there appears to be a tiny resister on the Main Board that could possibly be a bit charred.

Next

Akai Manuals

akai tv manual lct42z6tm

Menus will work until a video source Component is plugged into the tv. Your tv is hd ready one, not full hd. Upload date: 29 December 2013 Downloads: 512 since 29 December 2013 Information: 1. Either they have a flaw in the design, but more probably they had a poor supplier of the Capacitors. The image and sound are transmitted very clearly and accurately. Twisted stress is not applied to the module. Didn't need to add solder, just clipped the leads down to about 1 cm and spread them the same width then heated underneat to drop one leg in, the the other.

Next

Akai Manuals

akai tv manual lct42z6tm

Failure to comply with these rules may result in being banned from further commenting. Mute : Press this button to quiet the sound system. Tegnap valami történt a fent megnevezett tv típussal, magától összeugrott a kép a felére kb. It could be done, but it would be at the expense of other channels. Replace the back and the screws. Revision Date Page Description Feb. This really should be some sort of class action suit since they are all failing about 1.

Next

AKAI LCT42Z6TM SPECIFICATION SHEET Pdf Download.

akai tv manual lct42z6tm

Will look for C301 next, is it on the signal board? I've never done anything like this but had no problem. Please observe all warnings displayed on your electronic devices. The matrix employs a-Si Thin Film Transistor as the active element. The pi cture tube is a Many e lectrical an d mechanica l parts in this vacuum and if bro ken, the gl ass will explode. The toughest part was geting the wire connectors off without pulling the wire apart. This is only added protection and works fine. Hope that explains it for you sufficiently! Remélem mükszik majd :D Sziasztok! Carefully remove all of the wires, taking time to remove the glue from the connectors.

Next

AKAI LCT42Z6TM SERVICE MANUAL Pdf Download.

akai tv manual lct42z6tm

I have seen this before and we will probably see it again. Ha a sormeghajtó bázisára külső jelet adok akkor elindul a gép, nagyfesz, képcsőfűtés rendben, van fény. They are call fairly common. It will display a television signal on that left side as well just fine with sound. Another note, there appears to be a tiny resister on the Main Board that could possibly be a bit charred.

Next

AKAI LCT42Z6TM SPECIFICATION SHEET Pdf Download.

akai tv manual lct42z6tm

It's the best place I know to find the parts you need. Symptom may have four boxes in each of the corners of the screen. Posted on Oct 11, 2008 There are three caps that always pop on that psu board. I am having the same problems as everyone else on this blog. Sooner or later, they should acquire one. Be sure to get them right. Option 2 Fix the signal board.

Next

Akai Full HD LCD TV

akai tv manual lct42z6tm

Electronics and electrical engineering «Akai», in its time, was very popular, as the quality of products has always been on top. Néha próbál szélesedni, formálódni, olyankor már kezd négyszögre hasonlítani és felülről közelít a 15625 Hz-hez, de leginkább ez a rángatózás látható, ami nem elég a meghajtáshoz, folyamatosan leülteti a meghajtó tranyót. Those capacitors you mentioned: Are they labeled inside so that i can just change them out? Please comment and like if you find this helpful - this video is made for the youtube community for education. I have inspected them and visually I see no issues. But once I got them off I also took pics of the wires I unplugged after tagging them with numbers so I knew where they went back to. How do i know where they are at? Are they easy to replace? Ennek következménye hogy nem tudom újra előhívni a menüt hogy átállítsam, mivel bekapcsolás után fekete kép jelenik meg.

Next

TV Repair

akai tv manual lct42z6tm

Electrostatic Discharge Control Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Also, figuring out which lead was and which was - was tought. The toughest part was geting the wire connectors off without pulling the wire apart. This information should only be used to help diagnose work, and all service should be performed by a qualified technician. Black Level : Surface Luminance of Black L is the luminance value at center 1-point. Sometimes after turning on and off a few times the whole screen will display so it is intermittent. Újra kellene írni az eeprom-ot????? It is a transmissive display type which is operating in the normally black mode.

Next

Service Manual Akai

akai tv manual lct42z6tm

This worked like a champ and took me two hours total. Are you sure that thsoe are teh only ones that need replaced? Take your time with the big connector on the left side. Color Data Reference The brightness of each primary color red,green,blue is based on the 8-bit gray scale data input for the color. Eddig nincs is semmi gond de addig piszkálgattam hogy sikeresen el. Make certain that treatment persons are connected to ground through wrist band etc.

Next

SOLVED: Akai LCT42Z6TM HD 1080P TV

akai tv manual lct42z6tm

A készülék egyébként 50 Hz-es. Electrical Characteristics It requires two power inputs. Posted on Jul 21, 2014 The tv is having a problems with the board called T-Con board it is dying and the problems. Once set correctly, you should have a great picture once again. Should I just replace all the caps on the power supply board? Finally just bought a 15 dollar soldering iron and four caps off Amazon. Didn't need to add solder, just clipped the leads down to about 1 cm and spread them the same width then heated underneat to drop one leg in, the the other. Number buttons: Use these buttons to enter the password.

Next