Harley davidson plug wiring diagram. Plug and Play Trailer for Harley Davidson 2019-03-01

Harley davidson plug wiring diagram Rating: 4,4/10 1262 reviews

Harley Wiring Connectors

harley davidson plug wiring diagram

Tighten to 30-40 ft-lbs 40. Ring sets are available to fit oversize pistons. Be sure that brake fluid or other lubricants do not contact brake pads or discs. Screw throttle cable adjuster until it is as short as possible. . Loosen the pinch bolt 4.

Next

Harley Davidson Wiring Diagrams DIY

harley davidson plug wiring diagram

Oil Pump O-rings from chain guide bracket assembly. Install hone in a high speed electric drill. Grease Fitting 1-48 2008 Softail Service: Maintenance. Minimum free length for spring 3 is 1. Sequential number varies Table 2-11. All that position does is turn on the rear tail lamp and nothing more. I am struggling to find any information on this bike online but am very interested in finding out more about the history of this bike.

Next

Sportster Harley

harley davidson plug wiring diagram

Second compression ring Figure 3-123. Pull seat to the rear to disengage tongue 1 from the frame. Insert the flanged end of dust boot into the insert mounting bolt through caliper bracket 13 and upper internal groove of the top caliper mounting lug. Remove main fuse holder from storage posi- tion. Pillion Support fastener 4 2. . Installing Bearing in Shaft Support sm02830 Front and Rear Balance Sprockets Figure 3-168.

Next

Sportster Harley

harley davidson plug wiring diagram

Primary drive locking tool Figure 6-8. Transmission Power Flow 2008 Softail Service: Transmission 7-3. Wipe any foreign material from plug. The next two years Harley and his childhood friend Arthur Davidson labored on their bike with an engine using a garage in the house of their friend, Henry Melk. Remove nesting ring 7 at back of auxiliary lamp 8.

Next

Harley Wiring Connectors

harley davidson plug wiring diagram

Following the same sequence, tighten each bolt to 15-19 ft-lbs 20. Upper Spoke Row Completed Figure 2-47. For Solid Color Wires: See Figure B-1. Support motorcycle in an upright position so the front end Loosen the fork stem nut 2. Do not replace parts individually; ratchets should be rebuilt with the entire contents of service kit.

Next

Wiring Diagram Installation: DOWNLOAD A Harley Davidson Repair Manual

harley davidson plug wiring diagram

Thank you for all of your replies! See a Harley- Davidson dealer. If the brakes feel spongy, bleed the system again. Where should it be connected to in the other side? Pull main fuse from fuse holder. The tails should be folded in on the wire core without any distortion or excess wire strands. A-19 Mating Pin and Socket Housings. Measure Thickness of Support Plate Figure 3-134. Failure screw 8 and shifter rod lever 9 from the shifter pawl to replace this gasket may cause primary chaincase leaks.

Next

Wiring Diagram Installation: DOWNLOAD A Harley Davidson Repair Manual

harley davidson plug wiring diagram

Mainshaft 5th gear Figure 7-16. Remove push rods, lifters and covers. Make sure to read the instructions first. Right crankcase half Figure 3-53. Tighten to 14-21 ft- lbs 19. Use the proper grade of oil for the lowest temperature expected before next oil change. Do not smoke or allow open flame or sparks near gasoline.

Next

Harley Davidson WL civilian ignition switch help needed.

harley davidson plug wiring diagram

On the pin side of the connector, tangs are positioned at the bottom of each cavity, so the slot in the pin terminal on the side opposite the crimp tails must face downward. The fuel gauge is mounted in the left fuel tank cap. Disconnect tail lamp connector 2. Delphi Maxi-Fuse Housing: Bend Tang 2008 Softail Service: Appendix A Connector Repair A-11. Run engine until it reaches normal operating temperature.

Next

Harley Davidson Wiring Diagrams DIY

harley davidson plug wiring diagram

Oil Pump Torque Sequence 2. Remove Drive Components sm02396 1. Remove the brake hose bracket from the bottom of the fork stem and bracket 9. If your trailer has a 4 wire harness 4 pin flat connector then a 5 to 4 wire converter will be required. If lower handlebar clamps 7 were removed, install lockwashers 15 on lower handlebar clamp fasteners 16.

Next

Harley Davidson Plug Wiring Diagram • Auto Wiring Diagram

harley davidson plug wiring diagram

I did follow this and in fact this black wire goes directly to the knobb behind the ignition switch. Lower Row Spokes Spaced to Every 4th Hole Figure 2-44. An improper wattage sealed beam or bulb, can cause charging system problems. Primary drive locking tool 9. Groove in lower retainer Disconnect electrical harness from fuel pump. Always grasp a hammer handle firmly, close to the end.

Next