During this period, avoid full-throttle starts and rapid acceleration. For more options, visit this group at. Every Clymer motorcycle service manual is written for the do-it-yourselfer as well as the experienced mechanic, Clymer motorcycle repair manuals are the cheapest way to keep your motorcycle running properly. To ensure the best quality and reliability, use only new genuine Honda parts or their equivalents for repair and replacement. Refer to the indicators 4 neutral indicator frequently. Replacement Chain: The O-rings can be damaged by steam.
Using spark plugs with an improper heat range can cause engine damage. They may affect lubrication and clutch performance. Gasoline is highly flammable and explosive. Now that all seems to be fine. Remember, more frequent checks may be needed for riding in severe conditions.
We recommend wheel removal be done Remove the front axle nut. Insert the ignition key in the fuel fill cap and turn it clockwise. Tighten the upper lock nut and check the freeplay again. This, in addition to extensive research, is how Clymer repair manuals achieve an unmatched level of detail, accuracy and clarity to guide the reader through each service, troubleshooting and repair procedure. If a torque wrench was not used for installation, see your Honda dealer as soon as possible to verify proper assembly. Do not run the engine unless instructed to do so. I know this is an old post hoping someone can help.
Turn the upper clutch cable adjuster to obtain the specified freeplay. Wheel removal requires mechanical skill and professional tools. For more options, visit this group at. Wheel removal should normally be handled only by a Honda Failure to properly follow technician or other qualified mechanic. Thanks I also have a question. And operating this motorcycle safely is an important responsibility.
Stop the engine and keep heat, sparks and flame away. Installation Installation can be done in the reverse order of removal. However, the carburetors must be returned to standard factory specifications before riding again at lower altitudes below 5,000 feet, 1,500 m. Inspect the front and rear sprocket teeth for excessive wear or damage. If you have a tire professionally replaced at a non-Honda facility, we recommend that you have the work checked by your Honda dealer. Charge the battery page as required. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure.
It should only be O-rings, or otherwise appears removed or replaced by your Honda dealer. Tripmeter Reset Knob The reset knob is used to reset the tripmeter to zero 0 by turning the knob in the direction shown. Miles km Odometer Date Performed By: Notes 1,000 4,000 6,400 8,000 12,800 12,000 19,200 16,000 25,600 20,000 32,000 Servicing Your Honda. A friend of mine suggested heating it with a gun and then using a reverse drill bit to take it out. To unsubscribe from this group and stop receiving emails from it, send an email to.
Taking Care of the Unexpected. You can pay by check or money order, or charge to your credit card. To zero 0 the tripmeter, turn the tripmeter reset knob. Improper assembly may lead to a loss of braking capacity. Pull the battery out of the battery box.
High pressure water or air can damage certain parts of your motorcycle. Refer to the official Honda Service Manual page In the interest of safety, we recommend these items be serviced only by your Honda dealer. Whenever you add a your passenger is wearing the proper passenger or cargo, you must be careful protective apparel page not to exceed the total load limits for this vehicle. I have the original bracket and fuse box ordered of eBay. Production model years: 1984 Onwards. Remove the plug to drain the deposits in the tube.
If proper adjustment cannot be obtained by this method, see your authorized Honda dealer. Install the side collar and position the wheel between the fork legs. Also increase spring pre-load for stiffer rear suspension. Take care to avoid pinching any cables or wires. As the tire gets low, it will affect temporary tire or tube repair can the handling of your motorcycle be risky. Adjust idle speed with the throttle stop screw.
To post to this group, send email to. Your Honda dealer can inform you about. Wheel removal requires mechanical skill and professional tools. The drive chain should be checked, adjusted, and lubricated as part of the pre- ride inspection page Servicing Your Honda. To view this discussion on the web visit.