Follow the Maintenance Schedule recommendations to ensure that the engine is in peak operating condition. Move the control lever to the N neutral position. Its recommended to only use the exact tools, as specified in the factory 15 horsepower outboard manual. The last, most important task you can perform to help keep your gearcase in top shape, is to flush the inside and outside of the gearcase after each use. Remove recoil moving the three 6 mm bolts.
Honda Company is engaged not only in the production and sale of machinery, boats, but also in the manufacture of boat motors and all kinds of boat products and accessories for boats, yachts and catamarans. High altitude operation At high altitude, the standard rich. Remove the spark plug caps. If any oil leaks out or water enters, either the propeller shaft seal must be replaced or the gear case must be disassembled, inspected and completely overhauled. Check the engine oil level.
The most important tool in your toolbox may be your Clymer manual -- get one today. Refill to the upper mended oil see p. Clymer Honda Four-Stroke Outboard manuals are written specifically for the do-it-yourself enthusiast. Flush cooling the water hose joint optional. The water must be at least 4 inches the anti-cavitation Start the engine and run slowly at least 5 minutes.
Connect the fuel tank line to the motor. It compensates for the initial wear that occurs during the life of the engine. The Honda 4-stroke outboard motor is distinguished by its special reliability and practicality in use. Push and hold the stop button depressed until the engine stops running. Install the new ,propeller in the reverse sequence to removal. For safety, disconnect the spark plug lead, then ground it to the cylinder head. This manual should be kept near the machine for reference and periodically reviewed by all personnel who will come into contact with it.
The outboard marine mechanic should carefully read the text and become familiar with the 15 horsepower marine engine service manual procedures before beginning the work. If necessary for service or access, remove the propeller, for details refer to the procedure in the Maintenance and Tune-Up section. After starting the engine, return the lever slowly to the position the engine does not stall. N neutral : The engine idles and the transmission. The steering should move smoothly and freely. Transport and store the motor either vertically here, with the steering Vertical transport or storage: Attach stern stand. Engage the emergency stop switch clip, located at one end of the.
Spilled fuel is spilled, make sure the area is dry before storing motor. Performing the scheduled maintenance is very important. Once you've rinsed the outside, hook up a flushing device and do the same for the inside. If your dealer doesn't have an immediate answer, they should be able to get it for you. Is fuel reaching the carburetor? From basic maintenance and troubleshooting to complete overhauls, our Honda Four-Stroke Outboard manuals provide the information you need. These sections are not covered in this supplement. Remove the cotter pin, then remove the 14 mm castle nut, plain washer, and the propeller.
The second most important task for proper gearcase maintenance is checking and maintaining the oil inside the case. The gearcase contains the propeller shaft, the driven and pinion gears, the drive shaft from the powerhead and the water pump. Operators and maintenance personnel must read this manual before operating or maintaining this machine. On models equipped with shifting capabilities, the forward and reverse gears, together with the clutch, shift assembly, and related linkage, are all housed within the case. To turn to the left, Boats equipped in the same way as a car. On all motors except the 2.
To be honest, a complete overhaul is recommended, because corrosion and damage may have occurred if moisture was in the gearcase long enough. Always work in a well-ventilated Be sure that any fuel drained container. If any fuel is spilled, starting the engine. Remove the engine remove salt water, 2. Wind spare around pulley engine.
All information product information available at the time of approval for printing. Thoroughly inspect the gearcase and exhaust housing for signs of damage. Apply a light coat of clean liquid soap to the water tube grommet. After the spark plugs are seated, compress the washers. Check to see if the screen in the cooling Do not operate the engine is flowing out of the water out, or if steam water until the problem has been corrected.