These kit parts quicken throttle response to the twist grip. Tachometer with Water Temperature Gauge 25031-1142 4. To connect the shift up indicator Green. Replace the pulsing rotor with the kit rotor 21007-0085. To connect the right switch housing Black. To connect the left switch housing Black. Remove the related parts of the starter motor and insert the plugs to the hole of the starter motor inserted as shown in the illustration.
First Edition 1 : Feb. Install the kit water temperature sensor for water temperature gauge of kit meter, 21176-1099 to the kit water pipe. This is done to start easily the engine with the second gear. Install the cylinder head and adjust the camshaft chain timing. To adjust the cylinder compression to 14. To connect the inter face box Black.
Fix the brackets 11054-0459 on the sub radiator by the bolts 130L0612. To quicken response by reducing the flywheel mass and to reduce the weight, use the kit alternator. To connect the right switch housing Black. The back-torque limiter operating condition can be changed by changing the total thickness of clutch plates and changing the number of leaf springs. Plug 92066-1332 Plug 92066-1333 O-ring 92055-1262 Bolt 130G0625 312B0600 Calk the bolt for unplug the plug.
The back-torque limiter works to reduce the chance of rear wheel hop caused by engine braking during hard braking and down shifting. To connect the auto-shifter Blue. To connect the tachometer with water temperature gauge Black. To connect the Fuel Pump. Fix the stator to the cover by the bolts. .
Apply the engine oil to the tensioner rod, O-ring and tensioner body, insert them into the tensioner body. To adjust the cylinder compression to 14. This grid covers: B-14 Gear Change Mechanism Ref. Shift up Indicator Lamp 23016-0006 2. The difference between the highest and lowest gauge readings is the amount of the effective stroke of clutch spring plate.
All information in this manual is based on the latest product information at the time of publication. To connect the vehicle down sensor Gray. Auto Shift Functions Be sure use the point type sensor. To connect the shift up indicator lamp Green. Insert the plug into the hole of the starter motor and tighten the nut. Use the kit connecting rod assemblies 13251-0015. Kit Connecting Rod Connecting Rod Bolt Use the kit connecting rod bolts with the original connecting rod bolts and nuts.
This grid covers: Clutch Ref. To connect the atmospheric pressure sensor Black. To connect the original meter Black. Periodic Maintenance Chart The scheduled maintenance must be done in accordance with this chart to keep the motorcycle in good running condition. When using the original connecting rod bolts, make recesses at both ends of the original connecting rod bolt to measure its length and determine the bolt stretch. Water Inlet of Radiator Body Divide the original water hose 39062-0109 between the cylinder head and the radiator and insert the water pipe 39192-0039.
To change the gear ratios with combination the gears. Swingarm Left Side Brake Pads Kit Parts The front and rear brake pads for racing use are available. All information, illustrations and specifications contained in this manual are based on the latest product information available at the time of manual approval. To connect the speed limit switch Black. This grid covers: Oil Pump Ref. When outbreak the starting judder, use the spring plate assembly of the kit parts.
Select one of them in accordance with your race regulation. Semitransparent connector not use 5. Adjust the valve clearance and valve timing. Main Harness and Sub Harness Kit Part Main harness and sub harness are available for racing use as kit parts. Refer to the base manual listed below for information of the original model. Main Harness with Original Meter and Kit Meter : 26031-0328 Sub Harness with Original Meter : 26031-0425 Sub Harness with Kit Meter : 26031-0426.
Oil Catch Tank: 52001-0002 Tank Capacity: Approximately 570 cc Oil Catch Tank Installation Install the mounting bracket 11054-0455 with regulator under the cross pipe of the frame by the bolts use the original regulator mounting bolts. Tighten the nut 1 to 59 N·m 6. This grid covers: Handlebar Ref. This grid covers: Rear Hub Ref. Excessive clearances will cause the oil pressure at the crankshaft main journals to drop and lead to the damage of the bearing. To connect the inter face box Black. This grid covers: Fuel Injection Ref.