Mitsubishi 3000gt service manual 1991 1999. MITSUBISHI 3000GT 1991 SERVICE MANUAL Pdf Download. 2019-02-22

Mitsubishi 3000gt service manual 1991 1999 Rating: 6,3/10 926 reviews

MITSUBISHI 3000GT 1991 SERVICE MANUAL Pdf Download.

mitsubishi 3000gt service manual 1991 1999

Replace if defective or cracked. Brake caliper mounting bolt l I 14. Caution When removing the lock pin, turn the control lever to such position that the lock pin will not contact the clutch housing. Any loose or protruding parts of damaged vehicle such as hoods, doors, fenders, trim, etc. The vehicle number is a code which tells country, make, vehicle type, etc. Check each bushing for wear or abrasion, sticking, impeded action, and damage. If any parts other than describes below are defective, replace the transaxle assembly.

Next

Mitsubishi GTO (3000GT) Workshop Service Repair Manual

mitsubishi 3000gt service manual 1991 1999

Lock nut: 29 Nm 21 ftlbs. Brake caliper mounting bolt 6. Caution Secure the solenoid valve and oil temperature sensor. Throttle position sensor within idle position switch 5. Remove the hub cap and then release the parking brake. Measure the thickness of the solders crushed with a micrometer and select a spacer to obtain the specified preload. Air intake hose A 4.

Next

Mitsubishi 3000 GT Workshop & Owners Manual

mitsubishi 3000gt service manual 1991 1999

Note that the following must never be done: Unauthorized modifications of any electrical device or wiring, because such modifications might lead to a vehicle malfunction, over-capacity or short-circuit that could result in a fire in the vehicle. Brake line clamp bolt 5. Shift lever assembly removal steps Transaxle control cable assembly removal steps 1. Check whether the turbine wheel and the compressor wheel can be easily. Air pipe m -- 3. Clutch pedal Removal steps 14.

Next

Mitsubishi

mitsubishi 3000gt service manual 1991 1999

Catalytic converter and center exhaust pipe installation bolts 9. Plug the nipple of the solenoid valve from which the hose black has been disconnected. Overfill limiter Two-way valve side 5. If, however, there is enough space to insert a screwdriver or the like behind the clip, use the following procedure for ease of work. It is important to get the right repair manual for Mitsubishi Pajero Sport. Caution Pulling the drive shaft can cause damage to the T. Be sure to check the battery for voltage and other conditions before starting the test.

Next

Tech

mitsubishi 3000gt service manual 1991 1999

Cruise control pump and link assembly 3. Keep Your Vehicle Running Smoothly. Do not use solvent to clean the following parts: Throttle position sensor Idle position switch Idle speed control servo. Checking of the Oil Pump Pressure Refer to P. Side air dam Rear spoiler removal steps Trims. Hint 2: If the pressure indication of the barometric pressure sensor drops significantly during high speed driving, check the air cleaner for clogging.

Next

Mitsubishi

mitsubishi 3000gt service manual 1991 1999

Check the spring for deformation, deterioration or damage. Retain receipts for all vehicle emission services to protect your emission warranty. Front rotor Front speed sensor removal steps Refer to Group 42 - Fender. Caution After checking the engine speed, there must be a return to the standard idling speed. Drive pinion rear bearing outer race 5. Air cleaner, Air intake hose a 3. Check the drive shaft splines for wear or damage.

Next

➤ Download Mitsubishi 3000gt 1991 1999 Service Repair Manual Download Ebook PDF 2019 PDF E

mitsubishi 3000gt service manual 1991 1999

Lower arm mounting bolt Stabilizer link to lower arm Self-locking nut 9. Final Drive Gear Tooth Contact Refer to P. Attach a spring balance to the hub bolt, then, pulling the balance at a right angle to the hub bolt, measure the rotation torque rotation starting torque to see whether it is within the standard value. Bleed the air, and then turn the steering wheel several times while the vehicle is not moving so that the tempera- ture of the fluid rises to approximately 50 - 60°C 122 - 140°F. Move the float from top to bottom and check for continuity. Air hose D When equipped with intercooler left 3.

Next

Mitsubishi 3000GT Service Repair Manuals

mitsubishi 3000gt service manual 1991 1999

Grease: Repair kit grease 160 g 5. Check the brake pedal for bend or twisting. Connect a circuit tester to the brake fluid level sensor. Energy Conserving Oil In order to improve fuel economy and conserve energy new, lower friction engine oils have been developed. When checking a waterproof connector for circuit continui- Test harness ty, be sure to use the special tool, Test Harness.

Next

Tech

mitsubishi 3000gt service manual 1991 1999

Air cleaner, Air intake hose 1. Differential front bearing cap 72. When installing the V-ribbed belt, check that the V-ribs are properly fit without misalignment. Drive Check condition Check content Normal state A c t u a t o r t e s t 0 7 Fuel pump is Engine cranking Hold return hose with Pulsation is felt driven to cir-. Oil pump gasket Oil filter bracket stay 22. Does check engine light illuminate? If the difference between the brake drag force and hub rotating force exceeds the standard value, disassemble the piston and check the piston sliding surfaces for dirt and rust, piston seal for deterioration, and lock pin and guide pin for sliding motion.

Next

Mitsubishi 3000 GT Workshop & Owners Manual

mitsubishi 3000gt service manual 1991 1999

Front under cover center panel active aero system 11. Supplying of Transmission Oil Refer to P. Caution Cover the hose connection with rags to prevent splash of fuel that could be caused by some residual pressure in the fuel pipe line. Installation of the Shock Absorber Refer to P. Connector: Disconnected connector Check for an open-circuit, or a short- circuit to ground between the purge control solenoid valve and the engine control unit, Engine control unit connector: Disconnected Purge control solenoid valve con- Repair the. Inspect it for signs of contact with the compressor turbine. Removal and Installation of Main Muffler Refer to Group 15 - Exhaust Pipe and Muffler.

Next