Still not finished, but getting closer. Improper use of the product may be dangerous or illegal. It also features a High Security Disarm which allows a triggered alarm to be silenced without disarming the vehicle. Contact Viper customer service if the above methods do not work. Hold: is used after Press actions when a button needs to be held in position for an extended period of time, typically several sec- onds. If it was in anti-hijack mode, you would receive a warning like honking horn. Remote Start Safe-lock Remote start safe-lock makes sure the doors are locked while the en- gine is running and after, even if they are unlocked when remote start is activated.
Without knowing where this switch is you won't be able to disconnect the alarm. If it turns over your power and starter are good but the ignition circuit. The truck starts just fine with the remote start. If the above method does not work, put the key in the ignition, and turn it forward all the way just before cranking. If you need to dispose of the battery, please do so in accordance with your municipal requirements for battery disposal.
See Owner Recognition follow- ing for details. I have not hooked up the H2 Green passenger or rear door wires yet as the colours and locations have changed. Due to transit and storage time prior to your purchase, the battery charge may have depleted. Might just be an issue because I haven't finished the door wires yet, but also seems like the diodes may cause an issue there? My husband has a remote start the dealership put in, and if you're not close to the vehicle to hear the horn beep, you're out of luck. The only thing I'm not really sure about is the Ignition 1 vs Ignition 2 and Starter 1 vs Starter 2. Safety First Please read the safety warnings below before proceeding. If the door is opened in Step 3 then the engine continues to run.
I got the remote start to work wiring the alarm and disarm wires but the doors would not unlock. The distance is great on it! To ensure proper operation, check the battery level and connect the battery charger if not fully charged. Bad Neutral Safety Switch of which I am aware is bypassed by remote start only when installed? Put the key in and the truck barely starts due to the battery being weak. When starting my truck it often takes two or three attempts. It tries 3 times and gives up. I know how to properly connect wire, etc. Basic commands control the most often used security and remote start fea- tures while Advanced commands control more specialized features and request reports.
So I took it to a professional installer and he verified that my arm and disarm wires needed to be disconnected. It turns out that it was the hood pin I installed for my viper alarm. To perform Pit Stop: With the engine running, set the parking brake and release the foot brake. Now that I have the brain set for my Auto transmission the remote start button gets the truck cranking, but it wont fire. When the timer expires the engine starts and the message is sent to the remote control. Note: When the icon is without an arrow head: Smart Start is On; Remote Start is Off.
If you have any questions, ask your retailer or contact Directed directly at 1-800-753-0600. To reset a Viper car alarm, use the key fob by pointing it at the vehicle. When set to it wakes up every few seconds to listen for pages from the system. I got this for my daughter last year and for me, and it works like a charm. When set to it does not wake up to receive remote start or alarm trigger pages. Thanks for using FixYa May 24, 2010.
When the alarm is going off, allow it to do so for 6 seconds. Remote Start Time-out Alert During remote start a message is sent three minutes before and again at one minute before the engine turns off. At first, I thought it might be my wheel bearings or sway bar end links. Turbo Timer Mode The system keeps the engine running for the Turbo Timer runtime and can be activated by remote control or optional dash mounted activa-. The vehicle is ready to drive.
When entered, the alarm functions are defeated while the conve- nience features still operate normally. Locked: The system is Locked in Valet, the alarm is disabled. Some consumers, however, have had issues with the alarm system after replacing a battery. If it was really 8, the lights would be dim? Maybe your key fob is not synced to the alarm system. Slide the battery cover up by ap- Rear View plying equal pressure at its top and bottom the arrow on the cover indi- Battery cates the direction , remove the cover. I bled the fuel filter looking for air, but good fuel came out the top bleede.
When disarmed, the report will display text to identify the two most recent triggers since the ve- hicle was last driven. Glad to report a near perfect install on a 2014. The other car one in video has the Viper 5701 system in it. The wiring schematic I found on modifiedlife. I had the same problem that the remote won't pair with the system no matter what. Not finding clear guidance after almost breaking google.
Low Battery Alerts When disarming the system using a remote with a low battery the siren will emit one additional chirp as an alert. If you have all of your paperwork from the alarm system there should be a book that can help walk you through the reprogramming mode. Icon Description Armed: The system is Armed, the alarm is enabled. Just the crank process via the key is my issue. Could be another installed accessory or the car itself has a problem.